MEASURING INSTRUMENTS CATALOG No.E2019
410/608

F-71FMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.Set Conguration: Metric Full setPlus setPlus setSet Conguration: InchFull setBasic setø1 mm contact point (carbide)ø3 mm contact point (carbide)Stem, ø4 mmSwivel clamp(900321, for ø4 mm stem, ø8 mm stem, and dovetail)Metric holding bar (L: 100 mm)IndicatorKnurled clamp ringStem, 0.375 inch DIA.DIMENSIONSunit: mmSPECIFICATIONSMetric Horizontal (20° tilted face) typeOrder No.Graduation (mm)Range (mm)Dial readingMPE* (μm)Mass (g)Measuringforce (N)RemarksBasic setPlus setFull setMeasuring range One rev.10 scale divisionsHysteresis Repeatability 513-444-10E513-444-10A513-444-10T0.011.60-40-01610553480.3 or less44513-445-10E513-445-10A513-445-10T0.0020.40-100-0 6 524144Inch Horizontal (20° tilted face) typeOrder No.Graduation (in)Range (in)Dial readingMPE* (in)Mass (g)Measuring force (N)RemarksBasic setPlus setFull setOne rev. First 2.5 rev.Hysteresis Repeatability —513-442-10A513-442-10T0.00050.060-15-0±0.0005±0.00050.0002±0.0002480.3 or less44—513-442-16A513-442-16T0.3 or less44Black dial—513-446-10A513-446-10T0.2 or less444—513-446-16A513-446-16T0.2 or less444Black dial—513-443-10A513-443-10T0.00010.0160-4-0±0.0002±0.00020.0001±0.000040.3 or less44—513-443-16A513-443-16T0.3 or less44Black dialMetric Vertical typeOrder No.Graduation (mm)Range (mm)Dial readingMPE* (μm)Mass (g)Measuring force (N)RemarksBasic setPlus setFull setMeasuring rangeOne rev. 10 scale divisions Hysteresis Repeatability 513-456-10E——0.010.50-25-06—543460.3 or less4513-454-10E513-454-10A513-454-10T0.80-40-09—4513-455-10E513-455-10A513-455-10T0.0020.20-100-04—2314Metric Parallel TypeOrder No.Graduation (mm)Range (mm)Dial readingMPE* (μm)Mass (g)Measuring force (N)RemarksBasic setPlus setFull setMeasuring range One rev. 10 scale divisions Hysteresis Repeatability 513-486-10E——0.010.50-25-06—543530.3 or less4513-484-10E513-484-10A513-484-10T0.80-40-09—4513-485-10E——0.0020.20-100-04—2314Inch Parallel TypeOrder No.Graduation (in)Range (in)Dial readingMPE* (in)Mass (g)Measuring force (N)RemarksBasic setPlus setFull setOne rev. First 2.5 rev. Hysteresis Repeatability —513-482-10A513-482-10T0.00050.030-15-0±0.0005—0.0002±0.0002530.3 or less4* Horizontal (20° Tilted Face) Type, Vertical Type: We guarantee the accuracy of completed products by inspecting them with the dial face facing upward. Parallel Type: We guarantee the accuracy of completed products by inspecting them with the dial face vertical.Note: Stem with dovetail groove is not included in the mass.Inch Vertical typeOrder No.Graduation (in)Range (in)Dial readingMPE* (in)Mass (g)Measuring force (N)RemarksBasic setPlus setFull setOne rev.First 2.5 rev.HysteresisRepeatability513-452-10E—513-452-10T0.00050.030-15-0±0.0005—0.0002±0.0002460.3 or less4513-453-10E—513-453-10T0.00010.0080-4-0±0.0001—0.0001±0.000040.3 or less4With revolution counterLong stylusCarbide contact point (Slightly magnetic)0.039 inch DIA. contact point (carbide)0.118 inch DIA. contact point (carbide)Stem, 0.157 inch DIA.Swivel clamp (900322, for 0.157 inch DIA. stem, 0.375 inch DIA. stem, and dovetail)Inch holding bar (L: 4 inch)Dial Test IndicatorsComparison measuring instruments which ensure high quality, high accuracy and reliability.Order No.L1L2513-445-10E18.715.2513-444-10E20.917.4  8.71624.117.6ø4059.7ø8 0-0.0355.7L1L220°Order No.L1L2513-454-10E20.917.4513-455-10E18.715.2513-456-10E22.218.720.324.1759.4L2L155.417.6ø40ø8 0-0.03Order No.L1L2513-484-10E20.917.4513-485-10E18.715.2513-486-10E22.218.7※背面にアリ板はありません。8.817.624.1ø40L1ø8 0-0.0321.2L245.922.372.117.53.96.9Horizontal (20° Tilted Face) Type Vertical Type Parallel Type0.079 inch DIA. contact point (carbide)Note: A slight difference may occur depending on the center of the contact point, graduation plate, and stem xing position, etc.Knurled clamp ringStem, ø8 mmIndicatorø2 mm contact point (carbide)Basic set

元のページ  ../index.html#410

このブックを見る