F-11FMitutoyo operates a policy of continuous improvement that aims to provide the customer with the benet of the latest technological advances.Therefore the company reserves the right to change any or all aspects of any product specication without notice.ABSOLUTE Digimatic Indicator ID-CSERIES 543 — Calculation TypeFunctionsCalculation function f (x’) = Ax’ + B + Cx’ –1(x’ = x + offset)Peak detection function (Max/Min)Runout value Hold function (difference between max. and min. value motion)Peak detection sampling rate (Switchable)10 times/sec. (FAST Mode OFF)50 times/sec. (FAST Mode ON)Zeroset function (INC system)Preset function (ABS system)Tolerance judgement function (P1, P2, P3, and INC can be stored)Analog bar resolution selectable functionKey lock functionDisplay hold function (when external device is connected)Data output functionExternal PC setting input function (330°)Low battery/voltage alarm displayError alarm displayResolution switching function*5*5: Since the calculation resolution is one micrometer (0.001mm), using sub-micrometer resolution settings may result in the 4th-place digit being unreliable, particularly when B is set to a very low value and C =0. It does not change at all with certain combinations of calculation coefcient (for example, A = 1, B = C =0). The 3rd-place digit representing micrometers (if displayed) is always reliable.Optional Accessories• Lifting Lifting lever: No.21EZA198 (ISO/JIS/DIN Type), No.21EZA199 (ASME/ANSI/ AGD Type) Lifting knob: No.21EZA105 (ISO/JIS/DIN Type), No.21EZA150 (ASME/ANSI/ AGD Type) Lifting cable : No. 540774• SPC Cable: No.905338 (1m) No.905409 (2m)• USB Input Tool Direct (2m) : No.06ADV380F• Connecting Cables for U-WAVE-T (160mm) : No.02AZD790F For footswitch : No.02AZE140F Refer to page F-60 for details.• Digimatic Mini-Processor DP-1VR : 264-504• Parameter setup kit : No.21EZA313Note: Parameter setting software (can be downloaded freely from Mitutoyo website) is also required.• Contact points for Mitutoyo’s dial indicators (Refer to pages F-51 to F-54 for details.)• Measuring stands (Refer to page F-79 to F-85 for details.)• Calculation function operates on spindle displacement.• Entering the appropriate formula factors for a xture dedicated to the application enables direct measurement readout, thereby eliminating any need for the conversion tables previously needed for those applications where xtures are typically used.• Peak-Value Run-out/MAX/MIN Hold enables GO/±NG judgement for peak value.• Simple operation of many functions with ve buttons and status icons.• Wide LCD and new analog bar graph are now standard on all models.• Sampling can be performed fty times per second for accurate detection of maximum, minimum and run-out values.Resolution (mm)0.00020.0050.10.00050.010.20.0010.020.50.0020.051Resolution (inch)0.000010.00020.0050.000020.00050.010.000050.0010.020.00010.0020.05Digimatic IndicatorsComparison measuring instruments which ensure high quality, high accuracy and reliability.SPECIFICATIONSMetricOrder No.*RangeResolution (selectable)Accuracy*1Hysteresis*1Repeatability*1Measuring forcePower supplyBattery life (normal use)*2Net weight543-340B12.7mm12 steps*50.003mm0.002 mm0.002 mm1.5N or lessCR2032 x 1 pc.Approx. 1 year170 g543-590B25.4mm1.8N or less*3190 g543-595B50.8mm0.006mm2.3N or less*3260 g* Flat back onlyInch/MetricOrder No.*Resolution (selectable)RangeAccuracy*1Hysteresis*1Repeatability*1Measuring forcePower supplyBattery life (normal use)*2Net weight543-341B12 steps*5.5"/12.7mm±.00010" / 0.003 mm.00010" / 0.002 mm00010" / 0.002 mm1.5N or lessCR2032 x 1 pc.Approx. 1 year170 g543-342B543-591B1”/25.4mm1.8N or less*3190 g543-592B543-596B2”/50.8mm±.00025" / 0.006 mm2.3N or less*3260 g543-597B* Flat back onlyDIMENSIONSUnit: mmNote: All instruments in this series are of the at back type.The back is interchangeable with the standard backs for Series 2. Refer to page F-55 for details of the optional backs.*1 Does not include quantizing error (±1 count). Valid for resolution set to 0.001mm/'.00005" and coefcients A=1, B=0 and C=0.*2 Applies only if not connected to a data processor. Battery life depends on use of the indicator. Use the above value as a guide only. (TIP) Battery life with Peak detection mode and FAST mode ON is about 10 months.*3 Applies for a spindle orientation between the spindle pointing vertically downward to the spindle horizontal.*4 The resolution can be selected from one of 12 steps (Refer to table right).Note 1:Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator.Note 2:Inch (ANSI/AGD Type) dial indicators are provided with a stem of 3/8" dia. and #4-48UNF thread mount for the contact point.ISO/JIS Type(Refer to page X for details.)ø10.9ø8 0 -0.00950.146.516.821.27.354.413.3ø59.428.6ø4.87.6ø54Contact pointM2.5 x 0.45543-342BAn inspection certicate is supplied as standard. Refer to page X for details.ISO/JIS typeASME/ANSI/AGD type


page 352