MEASURING INSTRUMENTS CATALOG No.E2019
358/608

F-19FMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.• Enables a tolerance judgment to be output to external equipment for a measurement result against user-dened limits. Solid-state switching provides high reliability by avoiding metallic switch contacts. • Output is enabled by directly connecting to external devices (sequencers, etc., for which a logical invert is available if required). The measurement and judgment results are displayed on the LCD. The judgment result is also indicated by 2 LEDs. • A peak-detection function is equipped for measuring and judging peak values, such as runout.• Measurements are absolute (ABS system) relative to an origin point*1 as set by the user, which holds indenitely so does not require resetting at every power-on.• Provided with a 4 m cable.• External power supply required is DC5-24 V/ 100 mA (max).• Dust-water protection level: Conforms to IP54.*1 Regarding origin setting, refer to “Origin Setting of Digimatic Indicators” on page F-25.ABSOLUTE Digimatic Indicator ID-C SERIES 543 — Signal Output Function TypeDigimatic IndicatorsComparison measuring instruments which ensure high quality, high accuracy and reliability.543-350SPECIFICATIONSMetricOrder No. (w/lug, at-back)Range (mm)Resolution (mm)Accuracy*2 (mm)Measuring force (N)Overall*3HysteresisRepeatability543-350543-350B12.70.001/0.010.003 or less0.0020.0022.5 or lessInch/MetricOrder No. (w/lug, at-back)RangeResolutionAccuracy*2Measuring force (N)Overall*3HysteresisRepeatability543-351543-351B0.5 in /12.7 mm0.00005/0.0001/0.0005 in/0.001/0.01 mm±0.00010 in /0.003 mm or less0.0001 in/0.002 mm0.0001 in/0.002 mm2.5 or less543-352543-352B*2 Quantizing error of ±1 count is excluded. *3 Overall magnication and linearity.Note 1: LCD readout does not rotate.Note 2: MAX/MIN holding: sample rate is 100 readings/s; max. rate of change of reading is 100 μm/s.Note 3: Products with an Order No. sufxed “B” have a at backNote 4: Standard contact point: 901312 (ISO/JIS type), 21BZB005 (ANSI/AGD type)Functions• Signal output (–NG/OK/+NG, N-ch open drain, logical invert is available)• Remote control (peak start preset/zero-set)• Peak detection (MAX/MIN)• Runout range measurement (Difference between Max. and Min. values)• Zero-setting (INC system)• Presetting (ABS system)• Direction switching• Tolerance judgment (3 pairs of ABS, INC memory function)• Resolution switching • Calculation: f(x) = Ax• Key lock• Calibration mode (Signal output in Digimatic code format)• Error alarm displayOptional Accessories• Lifting*1 Lifting lever21EZA198 (ISO/JIS/DIN Type), 21EZA199 (ASME/ANSI/AGD Type) Lifting cable540774 Lifting knob21EZA105 (ISO/JIS/DIN Type), 21EZA150 (ASME/ANSI/AGD Type)• Digimatic power supply unit: 21EZA345 To denote your AC power cable add the following sufxes to the order No.: A for UL/CSA, D for CEE, DC for CCC, E for KC. No sufx is required for JIS/100VAC.Used in the calibration mode when executing automatic inspection using i-Checker IC2000.In such a case, purchase connecting cable21EAA194 (1 m), or 21EAA190 (2 m). Note: It can’t be used as a power suppy when using in the normal mode. • Contact points for Mitutoyo’s dial indicators.*2• Interchangeable backs for Series 2 models. Dust-water protection is not guaranteed. Use the waterproof types of Series 2 for plain backs if required.*3• Measuring stands (Refer to pages F-84 to F-92 for details.)*1 Dust-water protection is not guaranteed.*2 Refer to pages F-57 to F-60 for details.*3 Refer to pages F-61 for details.WireSignalI/ODescriptionBlack– V (GND)—Connected to minus (-) terminalRed+ V—Power supply (5 - 24VDC)Orange– NGOTolerance judgment result output: Only the terminal corresponding to a judgment result is set to the low level.GreenOKOBrown+ NGOYellowPRESET_RECALLZEROIExternal input terminal: If the relevant terminal is set to the low level, its signal becomes true.BluePEAK_STARTIShieldFG—Connected to GND (Earth)Note: Measurement data cannot be output.I/O SpecicationsWire– NGOK+ NGComposition errorOrange (– NG)LowHighHighHighGreen (OK)HighLowHighHighBrown (+ NG)HighHighLowHighLCD“x.xxE” indicationNote: Logical invert is available.Output signals and LCD displayInputOutputOutputOUT5-24 DCV1.2 kΩLoadGNDExternal power: 5 - 24 DCV at max.100 mA Input current: Max. 20 mAGNDSwitch, etc.INInternal circuitInternal circuitAn inspection certicate is supplied as standard. Refer to page U-11 for details. ISO/JIS type ASME/ANSI/AGD type

元のページ  ../index.html#358

このブックを見る