MEASURING INSTRUMENTS CATALOG No.E2016
354/682

F-13FMitutoyo operates a policy of continuous improvement that aims to provide the customer with the benet of the latest technological advances.Therefore the company reserves the right to change any or all aspects of any product specication without notice.• Enables a tolerance judgment to be output to external equipment for a measurement result against user-dened limits. Solid-state switching provides high reliability by avoiding metallic switch contacts. • Output is enabled by directly connecting to external devices (sequencers, etc., for which a logical invert is available if required). The measurement and judgment results are displayed on the LCD. The judgment result is also indicated by 2 LEDs. • A peak-detection function is equipped for measuring and judging peak values, such as runout.• Measurements are absolute (ABS system) relative to an origin point*1 as set by the user, which holds indenitely so does not require resetting at every power-on.• Provided with a 4m cable.• External power required is 5 - 24VDC.• Dust-water protection level: Conforms to IP54.*1 Regarding origin setting, refer to “Origin Setting of Digimatic Indicators” on page F-18.ABSOLUTE Digimatic Indicator ID-C SERIES 543 — Signal Output Function Type28.520ø10.97.6ø54ø59.47.337.213.813.367.443.550.15Cable: 4mø80−0.00920Ball contact (ø3)Order No.901312 (mount part: M2.5×0.45) 2028.520Digimatic IndicatorsComparison measuring instruments which ensure high quality, high accuracy and reliability.543-350SPECIFICATIONSMetricOrder No. (w/ lug, at-back)RangeResolutionAccuracy*2Measuring force543-350543-350B12.7mm0.001/0.01mm0.003mm or less2.5N or lessInch/MetricOrder No. (w/ lug, at-back)RangeResolutionAccuracy*2Measuring force543-351543-351B.5” / 12.7mm.00005/.0001/.0005” // 0.001/0.01mm±.00010” / 0.003mm or less2.5N or less543-352543-352BNotes: 1) LCD readout does not rotate.2) Max./min. holding: sample rate is 100 readings/sec; max. rate of change of reading is 100μm/sec.3) Products with an Order No. sufxed “B” have a at back4) Standard contact point: 901312 (ISO/JIS type), 21BZB005 (ANSI/AGD type)*2 Quantizing error of ±1 count is excluded. DIMENSIONSUnit: mmFunctionsSignal output (–NG/OK/+NG, N-ch open drain, logical invert is available), Remote control (peak start preset/zero-set),Preset, Zeroset, GO/±NG judgment (3 pairs of ABS, INC memory function) Max/Min/Runout value holding, Measurement direction switching, Power ON/OFF, inch/mm conversion (inch/mm models), Resolution switching, Scaling function f(x)=Ax, Key lock, Calibration mode (Signal output in Digimatic code format).Alarm: Counting value composition error, Overow error, Tolerance limit setting errorOptional accessories• Lifting*3 Lifting leverNo.21EZA198 (ISO/JIS/DIN Type), No.21EZA199 (ASME/ANSI/ AGD Type) Lifting knobNo.21EZA105 (ISO/JIS/DIN Type), No.21EZA150 (ASME/ANSI/ AGD Type) Lifting cableNo.540774• Digimatic power unit: 21EZA345 Note: To denote your AC power cable add the following sufxes to the order No.: A for UL/CSA, D for CEE, DC for CCC, E for KC. No sufx is required for JIS/100VAC.Used in the calibration mode when executing automatic inspection using i-Checker.In such a case, please purchase connecting cable21EAA194 (1m), or 21EAA190 (2m). • Contact points for Mitutoyo’s dial indicators.*4• Interchangeable backs for Series 2 models. Dust-water protection is not guaranteed. Use the waterproof types of Series 2 for plain backs if required.*5• Measuring stands (Refer to page F-75 to F-80 for details.*3 Dust-water protection is not guaranteed.*4 Refer to pages F-46 to F-49 for details.*5 Refer to page F-50 for details.WireSignalI/ODescriptionBlack– V (GND)—Connected to minus (-) terminalRed+ V—Power supply (5 - 24VDC)Orange– NGOTolerance judgment result output: Only the terminal corresponding to a judgment result is set to the low level.GreenOKOBrown+ NGOYellowPRESET_RECALLZEROIExternal input terminal: If the relevant terminal is set to the low level, its signal becomes true.BluePEAK_STARTIShieldFG—Connected to GND (Earth)Note: Measurement data cannot be output.I/O SpecicationsWire– NGOK+ NGComposition errorOrange (– NG)LowHighHighHighGreen (OK)HighLowHighHighBrown (+ NG)HighHighLowHighLCD“x.xxE” indication* Logical invert is available.Output signals and LCD displayLoadOUTGNDExternal power: 5 - 24DCV at 100mA max.Input current: Max. 20mA External power5 - 24DCV1.2kΩINGNDSwitch, etc.InputcircuitOutputcircuitNote 1:Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator.Note 2:Inch (ANSI/AGD Type) dial indicators are provided with a stem of 3/8" dia. and #4-48UNF thread mount for the contact point.ISO/JIS Type(Refer to page X for details.)An inspection certicate is supplied as standard. Refer to page X for details.ISO/JIS typeASME/ANSI/AGD type

元のページ 

page 354

※このページを正しく表示するにはFlashPlayer10.2以上が必要です