MEASURING INSTRUMENTS CATALOG No.E2016
212/682

C-43CMitutoyo operates a policy of continuous improvement that aims to provide the customer with the benet of the latest technological advances.Therefore the company reserves the right to change any or all aspects of any product specication without notice.• These ABSOLUTE Digimatic bore gages are exclusively designed for inside diameter measurement.• Up to four extension rods (250mm or 500mm) can be used for measuring at the bottom of a hole 2m deep.• ABS (ABSOLUTE) type bore gages are not subject to overspeed error. • The display and grip can be rotated up to 320 degrees and the display can be inclined up to 90 degrees, so that it is easily readable from any direction.• The minimum value holding function provides easy measurement of hole diameter.• Setting the Bore Gage to a master value using a gauge block set allows quick and accurate setting.• A Bore Gage Checker and a range of Setting Rings are available to aid in accurately setting a gage before making a measurement. (For details, refer to pages C-46 and C-47.)Bore GagesSERIES 511 — ABSOLUTE Digimatic Bore GagesBore GagesFor easy and accurate measurement of inside diametersTechnical DataAccuracy:Metric models 3μmInch models .00012"Excluding quantizing errorRepeatability:Metric models 2μmInch models .00008"Adjacent error:Metric models 2μmInch models .00008"Battery:SR44 (2 pc), 938882, for initial operational checks (standard accessory) Battery life: Approx. 2000 hours under normal use.Display: LCD character hight 8.5mmScale type: ABSOLUTE electrostatic linear encoderMax. response speed: UnlimitedFunctionPreset functionMaster value registration (3 values at maximum)Tolerance judgmentUpper/lower limit registration (3 values at maximum)Minimum value holdingData outputDisplay rotation (320°)Display inclination (90°, 7 steps)Low battery alarm displayError displayOptional Accessories21DZA089:Extension rod 250 mm (10”)21DZA081:Extension rod 500 mm (20”)Up to four extension rods can be jointed, and the maximum length 2m is allowed.Refer to page A-21 for detailsConnecting cables for Input Tool/ Digimatic Mini-Processor, etc. 1m: 905338 2m: 905409USB Input Tool Direct (2m): 06ADV380FConnecting cables for U-WAVE-T For standard (160mm): 02AZD790F For foot switch: 02AZE140F——— : Setting ring (See page C-47.)• Digimatic Mini-Processor DP-1VR: 264-504Example of connectionWhen connecting four pieces of 500mm extension rodsNotes: 1) Normal use is assumed to be 8 hours per day. 2) The correct peak value may not be displayed if the anvil's speed exceeds 50 μm/s. 3) IP53 indicates resistance to dust and dripping water, but only applies when the connector cap is in place.SPECIFICATIONSMetricOrder No.RangeStroke of contact pointMeasuring forceGuide forceResolutionContent of setProbing depthAnvilInterchangeable washerBattery (SR44)511-50145-100mm1.2mm5N or less10N or less0.001mm12 pcs.4 pcs.2 pcs.150mm511-502100-160mm13 pcs.4 pcs.2 pcs.InchOrder No.RangeStroke of contact pointMeasuring forceGuide forceResolutionContent of setProbing depthAnvilInterchangeable washerBattery (SR44)511-5211.8-4.0".047"5N or less6N or less.00005"/0.001mm12 pcs.4 pcs.2 pcs.6"511-5224.0-6.5"13 pcs.4 pcs.2 pcs.(Refer to page X for details.)

元のページ 

page 212

※このページを正しく表示するにはFlashPlayer10.2以上が必要です