MEASURING INSTRUMENTS CATALOG No.E2016
210/682

C-41CMitutoyo operates a policy of continuous improvement that aims to provide the customer with the benet of the latest technological advances.Therefore the company reserves the right to change any or all aspects of any product specication without notice.• Capable of ID (inside diameter) measurement close to the bottom of a hole.• Carbide contact point ensuring high durability and wear resistance.• Grip is large and hollow to reduce effect of body heat on high-accuracy measurements.• Alternative indicators may be used in place of those recommended*.* Some indicators and protection covers cannot be used with these bore gages. Contact a Mitutoyo sales ofce if considering the use of dial or digimatic indicators other than the recommended models.• Optional extension rods can be attached for measuring deep holes. (For details, refer to page C-45.)• A Bore Gage Checker and a range of Setting Rings are available to aid in accurately setting a gage before making a measurement. (For details, refer to pages C-46 and C-47.)Bore GagesSERIES 511 — for Blind Holes15-35mm/.6-1.4"35-60mm/1.4-2.4"50-150mm/2.0-6.0"Bore GagesFor easy and accurate measurement of inside diametersTechnical DataAccuracy:Metric models 4μmInch models .00016"Repeatability:Metric models 1μmInch models .00004"Adjacent error:Metric models 1μmInch models .00004"Optional Accessories–: Dial indicator (See Chapter F)21DZA000: Dial protection coverRecommended dial indicators (see Chapter F)Metric models:2046SB (0.01mm)2972TB (0.01mm - One-revolution type)2109SB-10 (0.001mm)2900SB-10 (0.001mm - One-revolution type)Inch models:2922SB (.0005")2977TB (.0005" - One-revolution type)2923SB-10 (.0001")2910SB-10 (.0001" - One-revolution type)Recommended digimatic indicators (see Chapter F)Metric models:543-310B (0.001mm)Inch models:543-312B (0.001mm/.00005")* Indicators equipped with rubber bellows, such as water-proof types, cannot be used.Notes: 1) A 10mm (.4") sub-anvil is supplied with 511-415/425/435/418/428/438 and a 50mm (2") sub-anvil is supplied with 511-417/427/437/420/430/440. 2) It is not permissible to use a sub-anvil other than as supplied as a standard accessory, or widen a measuring range by using multiple sub-anvils. (The measurement accuracy in such cases is not guaranteed.)SPECIFICATIONSMetricOrder No.RangeStroke of contact pointMeasuring forceGuide forceContent of setProbing depthBore gageDial indicatorDial protection coverAnvilWasher511-41515-35mm1.2mm4N or less6N or less511-415Not suppliedNot supplied11 pcs.1 pc.150mm511-41635-60mm511-4166 pcs.4 pcs.511-41750-150mm5N or less10N or less511-41711 pcs.511-42515-35mm1.2mm4N or less6N or less511-4152046SB(Graduation: 0.01mm)21DZA00011 pcs.1 pc.150mm511-42635-60mm511-4166 pcs.4 pcs.511-42750-150mm5N or less10N or less511-41711 pcs.511-43515-35mm1.2mm4N or less6N or less511-4152109SB-10(Graduation: 0.001mm)21DZA00011 pcs.1 pc.150mm511-43635-60mm511-4166 pcs.4 pcs.511-43750-150mm5N or less10N or less511-41711 pcs.InchOrder No.RangeStroke of contact pointMeasuring forceGuide forceContent of setProbing depthBore gageDial indicatorDial protection coverAnvilWasher511-418.6-1.4".047"4N or less6N or less511-418Not suppliedNot supplied11 pcs.1 pc.6"511-4191.4-2.4"511-4196 pcs.4 pcs.511-4202.0-6.0"5N or less10N or less511-42011 pcs.511-428.6-1.4".047"4N or less6N or less511-4182922SB (Graduation: .0005")21DZA00011 pcs.1 pc.6"511-4291.4-2.4"511-4196 pcs.4 pcs.511-4302.0-6.0"5N or less10N or less511-42011 pcs.511-438.6-1.4".047"4N or less6N or less511-4182923SB-10 (Graduation: .0001")21DZA00011 pcs.1 pc.6"511-4391.4-2.4"511-4196 pcs.4 pcs.511-4402.0-6.0"5N or less10N or less511-42011 pcs.The dial indicator and protection cover are optional. Contact Points(Unit: mm)511-416511-415511-416511-417511-4172.52.5

元のページ 

page 210

※このページを正しく表示するにはFlashPlayer10.2以上が必要です