ASME/ANSI/AGD type ISO/JIS type 312ø432ø95079147100245ø495ø861105564445............../..4197025021237331-0.0012Inch/Metric*1 Valid for resolution set to 0.001 mm/0.00005 in and coefficients A=1, B=0 and C=0.*2 Error of indication for the total measuring range*3 Applies for a spindle orientation between the spindle pointing vertically downward to the spindle horizontal.*4 Applies only if not connected to a data processor. Battery life depends on use of the indicator. Use the above value as a guide only.Note: Flat-back type only.SpecificationsDimensionsFunctionsMetricResolution (selectable)Range (mm)12.725.450.8Order No.543-340B-10543-590B-10543-595B-1012 steps*4Resolution (selectable)Order No.Range543-341B-10543-342B-10543-591B-10543-592B-10543-596B-10543-597B-100.5 in/12.7 mm1 in12 steps*4/25.4 mm2 in/50.8 mmø10.9ø8 0 -0.009ISO/JIS TypeASME/ANSI/AGD Type2-16• Calculation f (x’) =Ax’+B+Cx’–1 (x’=x+offset)• Peak detection (MAX/MIN)• Runout (MAX - MIN) HoldNote: Peak detection Settings can be changed to:1) Sampling rate: 50 readings/s2) Capturing speed: 50 µm/s (max.)• Zero-setting (INC system)• Preset (ABS system)• Tolerance judgment (3 pairs of ABS, INC memory function)• Analog bar resolution selectable• Key lock1) Sampling rate: 10 readings/s 2) Capturing speed: 10 µm/s (max.)Maximum permissible error*1 (mm)MPEE*2Hysteresis MPEHRepeatability MPER0.0030.0020.006Maximum permissible error*1MPEE*2Hysteresis MPEHRepeatability MPER±0.0001 in /0.003 mm0.0001 in /0.002 mm±0.00025 in /0.006 mm28.6ø4.8Ball contact (ø3)901312(threaded: M2.5×0.45)7.6Unit: mmMeasuring force MPL (N)1.5 or less1.8 or less*32.3 or less*3Power supply0.002CR2032×1 pc.Measuring force MPL (N)Power supply1.5 or less0.0001 in /0.002 mm1.8 or less*3CR2032×1 pc.2.3 or less*3Resolution (mm)0.00020.00050.0010.0020.0050.010.020.05* Since the calculation resolution is one micrometer (0.001 mm), using sub-micrometer resolution settings may result in the 4th-place digit being unreliable, particularly when B is set to a very low value and C=0. It does not change at all with certain combinations of calculation coefficient (for example, A=1, B=C=0). The 3rd-place digit representing micrometers (if displayed) is always reliable.• Display hold (when no external device is connected)• Data output• External PC setting input• Display rotation (330°)• Low battery voltage alarm display• Error alarm display• Resolution switching*Battery life (normal use)*4Net mass (g)170190260Approx. 1 yearBattery life (normal use)*4Net mass (g)170Approx. 1 year190260ø0.43ø0.375 0Resolution (in)0.10.20.510.000010.00020.000020.00050.000050.0010.00010.0020.0050.010.020.05Unit: in1.13ø0.19Ball contact (ø0.12)21BZB005(thread: No. 4-48UNF)0.30Refer to "Optional accessories" on page 2-35.
元のページ ../index.html#109